How to Charge Ring Video Doorbell (2nd Gen)
Remove your 2nd Gen Ring Doorbell from its mount, connect it via micro-USB, verify the solid LED full-charge status, and securely reinstall it.
This guide shows how to charge ring video doorbell (2nd gen) in 5-8 hours. Start with remove bottom security screws; follow the safety notes and step checkpoints below.
Visual step map
See the full sequence before you start, then check off each step as you go.
0 of 5 steps checked
Materials and cost planner
Select the items you plan to buy, adjust any estimated price, and calculate the selected total.
Editable rough U.S. retail estimates. Estimated all listed: $64.00. Prices are planning estimates, not quotes — tax, store, brand, size and quantity will change them.
Time and finish planner
Estimate active working time from the number of steps in this guide.
File transfer time calculator
Estimate how long a download, upload or local transfer should take at a given connection speed.
Real transfer time is usually longer because of overhead, server limits, Wi-Fi conditions or other network traffic.
- Read the tools, materials, safety notes, and steps below for free.
- Tap See 20-second demo if you want to understand it first.
- Tap Start Camera Coach when you want hands-free help, or Voice-only if you do not want to use the camera.
- Allow camera and microphone. Point your phone at the work; the coach watches your progress and tells you the next step.
🧰 Required Tools & Equipment
- ✓ Ring orange screwdriver handle
- ✓ T15 Torx security bit
- ✓ 5V/1A or 5V/2A USB wall adapter
📦 Materials & Supplies
- ✓ Micro-USB charging cable
- ✓ Soft microfiber cloth
⚠️ Safety Checkpoints & Warnings
- • Use standard 5V USB power adapters; avoid high-voltage laptop or proprietary fast chargers that could damage the battery.
- • Do not strip the proprietary security screws by using incorrect flathead or Phillips screwdrivers.
- • Place the doorbell face-down only on a soft cloth to avoid scratching the camera lens.
📋 Step-by-Step Guide (5 Steps)
Remove Bottom Security Screws
Insert the star-shaped T15 security bit into the orange Ring screwdriver handle. Locate the two security screws on the bottom edge of the doorbell casing. Turn counter-clockwise until both screws are completely removed, setting them aside in a secure dish.
- • Both bottom screw holes are empty and open
- • Two small security screws are resting in a tray or dish
- • Using a Phillips bit which strips the star-shaped Torx head
- • Dropping screws into garden mulch or porch floor cracks
Unhook Doorbell from Mounting Bracket
Grip the sides of the doorbell firmly with your fingers. Pull the bottom of the doorbell outward away from the wall, then lift upward slightly to release the top locking hooks. Lay the unit face down indoors on a soft microfiber cloth.
- • Doorbell body completely separated from the wall bracket
- • Doorbell resting lens-down on a microfiber towel
- • Yanking straight outward without unhooking the top tab first
- • Prying with metal tools and cracking the plastic housing
Connect Micro-USB Charging Cable
Locate the micro-USB charging port on the back of the doorbell body. Insert the micro-USB plug firmly into the port with the narrow side aligned properly. Connect the other end of the cable to a powered 5V USB wall outlet adapter.
- • Micro-USB connector fully seated in the rear port
- • Blue LED circle on the front of the doorbell lights up or starts animating
- • Forcing the trapezoid-shaped micro-USB plug in upside down
- • Plugging into unpowered USB ports or low-output computer hubs
Verify Full Charge Status
Observe the circular LED light on the front of the doorbell as it charges. As the battery fills, the blue LED segments will progressively light up around the ring. Wait until the entire circular LED turns solid blue with no flashing or gaps before disconnecting.
- • Complete 360-degree circular blue LED ring glowing steadily solid
- • No flashing, cycling, or partially unlit LED segments
- • Disconnecting early when only a partial arc of the circle is lit
- • Confusing spinning pairing lights with charging progress
Remount and Secure the Doorbell
Disconnect the micro-USB cable. Hook the top lip of the doorbell into the top notch of the mounting bracket at a 45-degree angle, then push the bottom flush against the wall until it clicks. Reinstall the two security screws into the bottom edge using the T15 screwdriver bit until snug.
- • Doorbell sitting completely flush against the mounting bracket
- • Security screws driven flush into bottom edge without protruding
- • Overtightening the bottom screws and stripping the plastic thread inserts
- • Snapping bottom in without engaging top hook tabs first
Credit: inspired by an original tutorial by Ring — watch the original on YouTube.
Don’t have everything?
- No Ring orange screwdriver handle? Standard 1/4-inch hex driver handle fitted with a T15 Torx security bit
- No 5V/2A USB wall adapter? Standard 5V phone charger brick